Epson NX127 Wartungshandbuch PDF herunterladen (Seite 18)

Epson Stylus NX125/T13/NX130 series Revision F

Disassembly/Assembly Details of Disassembling/Assembling by Parts/Unit 18

Confidential

LD Roller Assy

 When removing the LD Roller Assy, follow the procedure below.

1. Release the hooks (x2) and remove the Gear 23T.

2. Release the hooks (x2) and slide the Shaft Gear 24T to the 0-digit side until the concave section of the gear comes to the bearing part of the

Pick Assy.

3. Remove the LD Roller Assy upward.

 When removing the LD Roller, remove the screws (x2) shown in the figure above.

When install the Torsion Spring, make sure to align the leg to the position as shown above.

Pick Assy

Step 2, 3

Shaft Gear 24TConcave sectionBearing

C.B.P-TITE SCREW 3x8 (TBD)

C.F.B-TITE SCREW 3x5 (TBD)

Hook

Step 1

Gear 23T

Step 2

Shaft Gear 24T

LD Roller Assy

LD Roller

LD Roller Assy

Torsion Spring

Leg of the

spring

Housing Buckler

 When installing the Friction Buckler and Friction Buckler R to the Housing Buckler, pay attention to the following instructions.

• Remove the Sheet BF2-A on the rear side of the Friction Buckler to be replaced, and secure the removed sheet with double-sided tape to the

new Friction Buckler.

• Install the friction bucklers to the Housing Bucklers with the cutouts facing forward.

 Install the buckler to the position as shown above.

Friction Buckler R

Housing Bucklers Friction Buckler

Cutouts

Friction Buckler

Friction Buckler R

Friction Buckler

Sheet BF2-A

Double-sided

tape

Housing Buckler (Friction Buckler)

Housing Buckler (Friction Buckler R)

Carriage

When replacing the Carriage, be careful about the following and

remove the Grounding Plate, Guide Carriage, Compression Springs

from the Carriage to be replaced, then attach them to the new

Carriage as shown in the figure above.

 Insert the protrusion of the Grounding Plate to the hole of the

Carriage, and align the dowels (x3) of the Carriage with the

positioning holes (x3) of the Grounding Plate.

 Secure hooks (x2) of the Guide Carriage by attaching them on

the holes (x2) of the Carriage.

Grounding Plate

Guide Carriage

Compression Spring

Positioning Hole and Dowel

Hook

Protrusion

Compression Spring

Porous Pad Front Paper Guide

When installing the Porous Pad Front Paper Guide, align the pad

with the ribs and protrusions of the Platen. After installing the pad,

make sure to fit it evenly 1.5mm lower than the standard surface.

Standard surface:

In the area with concaves and convexes on the

Porous Pad Front Paper Guide, use the level

of the concave section as a standard surface.

Rib

Protrusion

Jam Cover

When removing the Jam Cover, be careful not to lose the spring

installed to the dowel on the right side.

Jam Cover

Spring

Jam Cover

USB Cover

The USB Cover cannot be re-used once it is removed. Whenever

the cover is removed, make sure to replace it with a new one.

When removing the USB Cover, cut the hook securing the USB

Cover with a nipper. Be careful not to damage the Upper Housing

then.

Hook

USB Cover

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Epson NX127 Wartungshandbuch Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Epson NX127