Epson F7070 Einstellungsanleitung

Epson® SureColor® F7070 Setup Guide

10 | Installing the Printer12. Replace the plastic piece and then fasten it using the screws from step 7.Installing the PrinterYou need six people to

Installing the Printer | 112.Insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are in

12 | Installing the Printer4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stand’

Installing the Printer | 137.Open the front cover and remove the tape.8. Remove the media holding plates.9. Feed the long waste ink tube through the h

14 | Installing the Printer10. Feed the short waste ink tube through the bracket as shown. Then feed the end of the long waste ink tube into the top o

Installing the Media Feeding Unit | 1513.Place the caution label for your language over the English label, if necessary.Installing the Media Feeding U

16 | Installing the Media Feeding UnitCaution: The media feeding unit is heavy and requires two people to install. To avoid damaging the media feeding

Installing the Media Feeding Unit | 174.Attach the media feeding unit to the stand using four C screws.Note: Leave the screws loose until the service

18 | Installing the Media Feeding Unit7. Plug in the communication cable and thread it through the cable supports.8. Make sure the communication cable

Installing the Take-up Reel System | 19Installing the Take-up Reel SystemYou need the following parts to assemble and attach the take-up reel system:1

2 |ContentsUnpacking the Printer ...

20 | Installing the Take-up Reel System2. Lower the take-up reel onto the brackets.3. Attach the take-up reel using three C screws as shown.4. Attach

Installing the Take-up Reel System | 215.Connect the communication cable that is attached to the take-up reel system by running it through the horizon

22 | Setting the Language7. Thread the power cord through the cable supports. Connect the power cord to the printer and use the cable supports to rest

Adjusting the Media System | 23Adjusting the Media SystemAfter completing printer assembly and before loading media, mark the loading position on the

24 | Adjusting the Media System3. Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide. Align the right s

Loading Media | 255.Raise the media loading lever and remove the adjustment paper.Loading Media1. Turn on the printer.

26 | Loading Media2. Open the front cover and then raise the media loading lever.3. Loosen the screws on the roll holders and slide the roll holders t

Loading Media | 275.Using two or more people, move the media onto the roll holder, adjusting the roll holder as necessary. When the media is securely

28 | Loading Media7. Pull up the roll holder lever, slide the roll holder into the media roll, and tighten the roll holder screw.8. Turn the roll hold

Loading Media | 299.Pull the media into the printer. If the left end of the media is not at the center of the rectangular area as shown in the figure

Unpacking the Printer | 3Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the

30 | Loading Media12. Pull the media out until the right end is parallel with the scale marks on the two labels. Then lower the media loading lever.13

Installing the Software | 3114.Close the front cover.15. After loading the media, you will be prompted to choose setup and media options. Choose optio

32 | USB InstallationUSB Installation1. Power off your printer, then connect the USB cable to the printer and your computer.2. Insert the CD into your

Network Installation | 33Network Installation1. Make sure your printer is powered on.2. Connect the Ethernet cable to the printer and your networking

34 | Network Installation4. Follow the on-screen instructions to complete the installation, keeping the following points in mind:• Do not remove the c

4 | Unpacking the PrinterWhen choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct

Unpacking the Printer | 5Media System AssemblyThe items below can be found in the “Ink Supply System Cover 1” box.Media feeding unitTake-up reelReel b

6 | Assembling the StandAssembling the StandMake sure you have the following items before assembling the stand.1. Slide the large horizontal strut int

Assembling the Stand | 73.Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and left legs.4. Attach t

8 | Assembling the Stand6. Temporarily fasten the waste ink tube bracket using one B screw.7. Remove the four screws, then remove the plastic piece.8.

Assembling the Stand | 99.Slide the mounting pieces into the grooves, as shown.10. Remove the screw, align the bracket, then fasten the screw to the s