Epson UB-E02 Spezifikationen

UB-E02Technical Reference Guide10Base-T/100Base-TXEthernet Interface boardEPSONEnglish404999000

viii Rev. ASupported TM PrintersThe following printers can use the UB-E02. (The TM-J8000, TM-T285, and RP-U420 cannot use the UB-E02. For new model

Rev. A ixUB-E02 Technical Reference GuideHow to Use this GuideInstallation OverviewBe sure to read Chapter 1, “System Preparation,” before using the p

x Contents Rev. AContentsChapter 1 System PreparationSupported Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rev. A Contents xiUB-E02 Technical Reference GuideChapter 5 SpecificationsPrinter Connection . . . . . . . . . . . . . . . . . . . . . . . . . .

xii Contents Rev. A

Rev. A System Preparation 1-1UB-E02 Technical Reference GuideChapter 1 System Preparation1.1 Supported Operating Systems❏ Microsoft Windows 95, Win

1-2 System Preparation Rev. AThe following printers cannot use the UB-E02.❏ TM-J8000, TM-T285, RP-U4201.4 Other LimitationsBe sure to note the foll

Rev. A Installation 2-1UB-E02 Technical Reference GuideChapter 2Installation2.1 Installation PrecautionsWARNING ❏Before installing, disconnect the

2-2 Installation Rev. A2.2 Unpacking❏ UB-E02❏ UB-E02 User’s Manual2.3 Part NamesNote: This photograph shows the TM-T88III printer with the UB-E02

Rev. A Installation 2-3UB-E02 Technical Reference Guide2.5 UB-E02 InstallationCAUTION:Before installing the UB-E02, be sure to set the DIP switches

2-4 Installation Rev. A3. Tighten the screws.If you have removed an interface circuit board that was already installed, fix the UB-E02 using the rem

Rev. A Installation 2-5UB-E02 Technical Reference Guide7. Print a status sheet to check whether the UB-E02 is installed correctly by holding the swi

2-6 Installation Rev. A2.6 Initializing UB-E02All the parameters of internal settings for the UB-E02 can be set to the factory default values. Foll

Rev. A Installation 2-7UB-E02 Technical Reference Guide2.8 FAQ2.8.1 Q1. The printer does not operate correctly. ("Serial interface" is p

2-8 Installation Rev. A

Rev. A Utilities 3-1UB-E02 Technical Reference GuideChapter 3 Utilities3.1 Setting the IP AddressTo use the UB-E02 with TCP/IP, you first need to s

3-2 Utilities Rev. AWindows 951. Double-click the Network icon in the Control Panel; then check whether TCP/IP is in the list of installed network c

Rev. A Utilities 3-3UB-E02 Technical Reference Guide3. Select Microsoft from the list of manufacturers and TCP/IP from the Network protocols list. T

3-4 Utilities Rev. AWindows NT 4.01. Double-click the Network icon in the Control Panel to check whether the TCP/IP Protocol is installed. If it is

Rev. A Utilities 3-5UB-E02 Technical Reference Guide3. If you continue installing the TCP/IP protocol, the TCP/IP Configuration dialog box appears,

Rev. A iUB-E02 Technical Reference GuideCAUTIONS❏ This document shall apply only to the product(s) identified herein.❏ No part of this document may be

3-6 Utilities Rev. A2. Click Properties and check whether the Internet Protocol (TCP/IP) check box is checked. If not, click the check box.Note:Afte

Rev. A Utilities 3-7UB-E02 Technical Reference GuideInstallation with Windows 951. Unzip the file and start Setup.exe.2. Install the EPSON TMNet Win

3-8 Utilities Rev. A3.1.1.3 Setting with the EPSON TMNet WinConfig CAUTION:Because the same IP address is set for all UB-E02 units in the factory, d

Rev. A Utilities 3-9UB-E02 Technical Reference Guide CAUTION:When you cannot check the MAC address on the label on the UB-E02 that is installed on t

3-10 Utilities Rev. ANote:To confirm the current setting, print out the status sheet. Press down the switch more than 3 seconds in the printable sta

Rev. A Utilities 3-11UB-E02 Technical Reference Guide3.1.2 Setting the IP Address Using the arp/ping CommandYou can set the IP Address using the ar

3-12 Utilities Rev. A4. Set the IP address to the UB-E02 using the ping command.•Example: ping 192.168.100.2015. If the ping command is successful,

Rev. A Utilities 3-13UB-E02 Technical Reference Guide3.2 EPSON TMNet WinConfig FunctionsThis section describes the functions, including options of

3-14 Utilities Rev. A3.2.1 Menu BarThe table shows each item and its function.3.2.1.1 Tool MenuTime-out settingUse Time-out setting to set the time

Rev. A Utilities 3-15UB-E02 Technical Reference GuideSearch OptionsIf you want to show and set a UB-E02 that is controlled by TCP/IP and is outside

ii Rev. ARevision InformationRevision Page Altered Items and ContentsRev. A

3-16 Utilities Rev. A3.2.1.2 Settings PrinterYou can set the printer name. This also shows printer information.Item ExplanationPrinter name Set the

Rev. A Utilities 3-17UB-E02 Technical Reference GuidePrint serverYou can set administrator information. This also shows the printer server informati

3-18 Utilities Rev. ATCP/IP You can set the TCP/IP.Item ExplanationGet IP address Auto or Manual is selectable for the UB-E02.Set by PING Check the

Rev. A Utilities 3-19UB-E02 Technical Reference GuidePasswordThe EPSON TMNet WinConfig can set a password to protect the UB-E02 settings. The screen

3-20 Utilities Rev. A3.3 EPSON TMNet WebConfig FunctionsThis section explains each function of the EPSON TMNet WebConfig.Note:Launch a browser and

Rev. A Utilities 3-21UB-E02 Technical Reference GuideItem ExplanationInformation General Show the UB-E02 information.TCP/IP Show the TCP/IP informat

3-22 Utilities Rev. A3.3.2 Protocol Information and Settings3.3.2.1 General InformationItem ExplanationAdministrator nameShows the administrator na

Rev. A Utilities 3-23UB-E02 Technical Reference Guide3.3.2.2 TCP/IP Information Item ExplanationGet IP Address Shows the method of setting the IP ad

3-24 Utilities Rev. A3.3.2.3 SNMP InformationItem ExplanationCommunity Read Only Shows he Read Community information.Read/Write Shows the Read/Write

Rev. A Utilities 3-25UB-E02 Technical Reference Guide3.3.2.4 TCP/IP SettingItem ExplanationGet IP Address Select the method of acquiring the IP addr

Rev. A iiiUB-E02 Technical Reference GuideAbout This Guide This guide is intended to provide all information necessary for system planning, design, in

3-26 Utilities Rev. A3.3.2.5 SNMP Communication SettingItem ExplanationCommunity Read Only The setting is fixed to “Public.”Read/Write Set the Read/

Rev. A Utilities 3-27UB-E02 Technical Reference Guide3.3.2.6 SNMP IP Trap 1 SettingItem ExplanationTrap Set Trap 1.Address Set the Trap 1 Address.Co

3-28 Utilities Rev. A3.3.2.7 SNMP IP Trap 2 SettingItem ExplanationTrap Set Trap 2.Address Set the Trap 2 Address.Community Name Set the Trap 2 Comm

Rev. A Utilities 3-29UB-E02 Technical Reference Guide3.3.2.8 Administrator SettingItem ExplanationAdministrator Name Set the administrator name.Loca

3-30 Utilities Rev. A3.3.2.9 Password SettingItem ExplanationOld Password Input the old password.New Password Input the new password.Re-input Passwo

Rev. A Utilities 3-31UB-E02 Technical Reference Guide3.3.2.10 ResetItem ExplanationReset Resets the UB-E02 to its status when the power was turned o

3-32 Utilities Rev. A3.3.2.11 AdvancedItem ExplanationPhysical Layer Setting Set the communication method.

Rev. A 4-1 Programming SamplesUB-E02 Technical Reference GuideChapter 4Programming SamplesThis chapter describes the following:❏ Method of printing

4-2 Programming Samples Rev. A4.1 Method of Printing to the UB-E02The UB-E02 has lpr protocol as its general print protocol. It is easy to print by

Rev. A 4-3 Programming SamplesUB-E02 Technical Reference Guide4.2 Direct Printing by PORT91004.2.1 For Windows ConsoleThe program is a sample of p

iv Rev. AEMC and Safety Standards Applied Product Name: UB-E02Model Name: M155BThe following standards are applied only to the interface boards t

4-4 Programming Samples Rev. A /* send data */ send(sock, "EPSON\n", 6, 0); /* gracefully close */ shutdown(sock, 1);/* SD_SEND */ wh

Rev. A 4-5 Programming SamplesUB-E02 Technical Reference Guide4.2.2 For LinuxThe program is a sample of printing “EPSON UB-E02” to a TM printer wit

4-6 Programming Samples Rev. A4.3 Commands Sent to a TM Printer When the Power is OnWhen the power is turned on, the UB-E02 transmits the following

Rev. A 4-7 Programming SamplesUB-E02 Technical Reference Guide4.7 Printer Operation by the UDP CommandsBy using the UDP commands, the following inf

4-8 Programming Samples Rev. A4.7.2 03-0000 Retrieving Basic Information4.7.2.1 Reply data4.7.3 03-0010 Retrieving Status4.7.3.1 Reply dataOff-set

Rev. A 4-9 Programming SamplesUB-E02 Technical Reference Guide4.7.4 03-0011 Forced TransmissionTransmission is done, regardless of the flow control

4-10 Programming Samples Rev. A4.7.6 03-0013 Buffer Flash4.7.6.1 Reply data❏ This clears only the buffer of the UB-E02 and cannot clear the receive

Rev. A 4-11 Programming SamplesUB-E02 Technical Reference Guide4.7.8 Programming Sample4.7.8.1 For Windows Console/* UDP3289 programming sample for

4-12 Programming Samples Rev. A buf[11] = 0x00; buf[12] = 0x00; // Parameter length buf[13] = 0x00; /* send a packet */ i = sendto(sock, buf, 1

Rev. A 4-13 Programming SamplesUB-E02 Technical Reference Guide4.7.8.2 For Linux/* UDP3289 programming sample for LINUX * HOW TO BUILD * cc ludp.c

Rev. A vUB-E02 Technical Reference GuideCAUTION:Connecting an outdoor overhead LAN cable directly to your productConnecting an outdoor overhead LAN ca

4-14 Programming Samples Rev. A buf[13] = 0x00; /* send packet */ i = sendto(sock, buf, 14, 0, (struct sockaddr*)&addr, sizeof(addr)); /* re

Rev. A Specifications 5-1UB-E02 Technical Reference GuideChapter 5SpecificationsThe UB-E02 can be installed in the TM-series printers as an interfac

5-2 Specifications Rev. A5.3.2 Printing Functions❏ Printing by standard protocols (printing of network objects through a device driver❏ Socket prin

Rev. A Specifications 5-3UB-E02 Technical Reference Guide5.4.3 External appearance and connector locations5.5 Software Specifications5.5.1 Basic

5-4 Specifications Rev. A5.5.3 Status Inquiry and Setting Protocols5.5.3.1 HTTP ❏ Port number: 80❏ User name: EPSON❏ Password: None❏ Maximum sim

Rev. A Specifications 5-5UB-E02 Technical Reference Guide❏ PDU support Get Request Get Next Request Set Request Get Response Trap❏ Server port numbe

5-6 Specifications Rev. A5.5.4.2 IP Address Assignment by APIPA❏ Item to acquire: IP Address❏ Range of address: 169.254.1.0 to 169.254.254.255Any IP

Rev. A Specifications 5-7UB-E02 Technical Reference Guide5.5.5 Internal Settings 5.5.5.1 Item List o = possible × = impossibleItem Parameter Initi

5-8 Specifications Rev. A5.5.5.2 Internal Parameter Setting Methods1. Using the exclusive utility.2. Using a browser3. Using arp and ping commands (

Rev. A Specifications 5-9UB-E02 Technical Reference Guide5.5.6 Initializing To initialize the UB-E02 when the power is turned on or reset, the stan

vi Rev. ASafety Precautions This section presents important information to ensure safe and effective use of this product. Please read this section

5-10 Specifications Rev. A5.6 Environmental Specifications Temperature:0 to 50° C {32 to 122° F} Humidity:10 to 90% RH (non-condensing) 5.7 Storag

Rev. A Definitions A-1UB-E02 Technical Reference GuideAppendix A DefinitionsAASB— Auto Status Back: The feature that allows the printer to send the

A-2 Definitions Rev. ATCP/IP—Name given to the suite of protocols (including but not limited to TCP and IP) that govern the transmission and service

EPSONSEIKO EPSON CORPORATION Printed in Japan

Rev. A viiUB-E02 Technical Reference GuideIntroductionThe UB-E02 is the 10Base-T/100Base-TX Ethernet interface board designed for the EPSON® TM printe