Epson FEH300b Bedienungsanleitung

FEH300-1Display Attached [email protected] for MCUSER'S MANUALHardware - Additional Volume -5.7 inch model

1-31-2 System CompositionThe following illustration shows the system composition of @E.Terminal for MC 5.7 inch.RS-232C or RS-485FALDIC ALPHA5FALDIC

2-1Section 2 Specifications2-1 Specifications2-1-1 General specificationsItemsS pecification sNP5M0101-2S4/ 2L4, NP5N0011-2S4/ 2L4Physicalenv ironme

2-22-1 Specifications2-1-2 Display unit specifications(1) Display unit specificationsItemNP5M0101-2S4NP5N0011-2S4NP5M0101-2L4NP5N0011-2L4Display devi

2-32-1 Specifications(4) Interface specificationsItem S pecification sModular jack 8-pin(MJ1)ApplicablestandardsRS-232C, RS-485 (2-wire connection)Sy

2-42-1 Specifications(6) Drawing environmentItem SpecificationsDrawing method Exclusive configuration softwareDrawing tool Name of exclusive configur

2-52-1 Specifications(8) Function performance specificationsItem Specification sScreen s Max. 1024Screen memory (FLASH memory) Approx . 4.5 Mbytes (V

2-62-2 Dimensions and Panel Cut-outNote: Arrange SX bus expansion cable so thatradius of bend in the cable is at least 50mm.Plug/unplug the SX bus ex

2-7<Display>ԡ1) DisplayThis is the display unit.2) Power lamp (POWER)Illuminates in green when the display unit

2-82-3 Names and Functions8) Modular jack 1 (MJ1)Used for screen data transfer and connection with PLCs or other peripheral devices.9) Modular jack 2

2-9Communication (RS-232C, RS-422/485) with a controller is enabled via the serial connector (CN1).Bottom viewThe serial connector pins correspond to

Thank you for purchasing Display Attached Controller @E.Terminal 5.7 inch model.This hardware edition of the use’s manual describes particular specifi

2-102-5 DIP SwitchesDIP switches (1 to 4) are equipped on side of the display unit.When setting the DIP switches, turn the power off.(Use USB-CFREC)D

3-1Section 3 Installation3-1 Mounting Procedure(1) Mounting procedure1) Insert the @E.Terminal unit into the mounting panel (max. thick: 5 mm).

3-23-2 Power Supply Cable WiringWarningElectric shock hazard. Shut the power off before wiring the power supply cable. (1) Power supply cable wiringP

4-1Section 4 Inspection and Maintenance4-1 Battery ReplacementWhen the time comes to replacement the battery, replace it for a new one even if batter

4-24-1 Battery Replacement3) Disconnect the battery connector. Disengage the battery fromthe socket by pulling the battery toward you.4) Insert a new

Issued as FE consolidated edition, June 2011Gate City Ohsaki, East Tower,11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, JapanE-mail: micrex-sx@fu

Safety PrecaustionBe sure to read the “Safety Precautions” thoroughly before using the module.Here, the safety precaution items are classified into “W

Safety PrecaustionCaution Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is found. Failure t

Safety Precaustion[General Notes]- Never bundle control cables nor input/output cables with high-voltage and large-current carrying cables such aspowe

*Manual No. is shown on the cover.Prin ted on *Manual No. Revision contentsJun. 2009 FEH300-1 First editionRevisions

ContentsPrefaceSafety PrecautionsRevisionsContentsPageSection 1 General ...

1-1- @E.Terminal for MCProduct types Di splay size S pecification sNP5M0101-2S4 5.7 inch TFT color- 320 x 240 dots, DC power supply- Controller u nit-

1-21-1 Types- Auxiliaries and othersNames Types S pecification sBattery for display unit V7-BT Replacemen t lithium primary battery for the V8 seriesU