Epson Stylus Color 800N Einstellungsanleitung Seite 1

Setup GuidePrinted on recycled paper with at least 10% post-consumer contentN®Front.fm5 Page i Wednesday, October 15, 1997 3:53 PM

7Setup GuideLoading the Paper1. Slide the left edge guide all the way left and pull out the output tray extensions.2. Fan a stack of plain paper and t

8Setup GuideTesting the PrinterIf you want, you can run a test on your printer to see how it’s working. Follow the steps in Chapter 6 of your printer

9Setup GuideYou can now install the EPSON Net! utility software, which configures the Ethernet card.Installing EPSON Net!If you are using NetWare or T

10Setup GuideInstalling in Macintosh1. Create a folder for EPSON Net! on your hard drive.2. Insert the EPSON Net! for Macintosh installation diskette.

11Setup GuideIf you use NetWare 4.x, menus will differ slightly from the menus described in the following procedure, and you must select Bindery Emula

12Setup GuideUsing EPSON Net! for NetWare WindowsFollow these steps:1. Start EPSON Net! for NetWare. After a few seconds, the following dialog box app

13Setup Guide3. Click Edit to configure the printer. The NetWare Config dialog box appears:4. Choose the operating mode you want to use:◗ Print Server

14Setup Guide6. Click Add at the bottom of the dialog box to assign a print queue to your print server.The Add Queue dialog box appears: 7. For Print

15Setup GuideConfiguring for TCP/IPYou can configure the Ethernet card for TCP/IP if you are using a UNIX TCP/IP network, a Windows 95 peer-to-peer ne

16Setup GuideAssigning the IP AddressFor a Windows 95 peer-to-peer network you need to set the card’s IP address. Make sure the Ethernet card and prin

iiAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electr

17Setup GuideIf you receive 4 lines that say “Request Timed Out,” the card is not set up correctly. Check to make sure the card is on the same segment

18Setup Guide6. Follow the instructions on the screen, inserting the requested diskette or CD-ROM if necessary. When setup is complete, the Network Se

19Setup Guide3. Set the following options in the IP Config dialog box:◗IP address Determine and assign an IP address. Check with your network administ

20Setup GuideInstalling DLC in Windows NTMake sure Windows NT is running, and follow these steps to install DLC:1. Open the Control Panel. 2. Double-c

21Setup Guide6. Type a name for the port in the Name box. Make sure the name is not the same as an existing port, such as LPT1.7. Select the target no

22Setup Guide8. Click OK to exit the Create Printer dialog box. A dialog box from the selected model’s device driver appears.9. Set any printer-specif

23Setup Guide3. Click a zone to select it. To select multiple zones, press and hold the Shift key while clicking the zones, or click Select All. Then

24Setup Guide7. Set the following options in the AppleTalk Configuration dialog box:◗Available ZoneSelect the network zone where you want the printer

25Setup GuideIn Windows NT 3.5x, choose Run from the File menu in the Program Manager.3. Type A:\SETUP and click OK. If you’re not using drive A, subs

26Setup Guide10. Check the current settings and click Next. Follow the instructions on the screen. Select Yes and click Finish to restart Windows when

iiiContentsUsing Your Software and Manuals 1Setting Up Your Printer 2Getting the Printer Ready 2Installing the Ink Cartridges 4Loading the Paper

27Setup Guide3. If you inserted the CD-ROM and Windows starts the installation program automatically, go to step 4.If it doesn’t start automatically (

28Setup Guide5. Click Add Port.6. In Windows 95, click Browse and choose the server or EPSON_TCPIP_Printer that your printer is set up on. Then click

29Setup GuideMaking Macintosh Diskettes from the CD-ROMBefore you follow these steps, name the formatted diskettes you’ll use Disk1 and Disk2 (using a

1Setup GuideCongratulations on purchasing your new EPSON Stylus® COLOR 800N printer. This guide summarizes the process of setting up your printer and

2Setup Guide◗EPSON Type B Ethernet Interface Card Supplement Contains instructions for configuring and using the Ethernet card with a Macintosh networ

3Setup GuideYou’ll find these items inside:2. Place the printer flat on a stable desk near a grounded outlet. Leave plenty of room in back for the cab

4Setup Guide4. Before you plug in the printer, make sure the power is off. Check the Ppower button; it’s off when its surface is raised above the prin

5Setup Guide3. Lift up the black ink cartridge clamp.4. Open the black ink cartridge package. Remove only the yellow part of the tape. Do not remove t

6Setup Guide6. Push down the clamp until it locks in place.7. Press the X color cleaning button. The print heads move to the left again so you can ins