Rev.: B1 Aura Series (PP-7000II / PP-7000IIUSB) Thermal Printer IMPORTANT!!!! Please read carefully before using this prin
1 - 6 • Since the paper roll is highly thermal sensitive, please keep them in a dark place that is 20º and 65% RH when not installed in the printe
1 - 7 • Use of volatile organic solvents such as alcohol, ester and ketone on thermal paper can cause discoloration. • Some adhesive tapes on ther
2 - 1 II. QUICK START-UP A. LOADING PAPER 1. Desk top application 1. Slide the hood lock toward the front of the printer to release the hood.
2 - 2 2. When to replace paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for r
2 - 3 please adjust in setup window the switch positions both 1, and 2 to ON leaving the rest unchanged as factory default setting. 3. USB connectio
2 - 4 Follow the wizard and browse to the folder that holds the driver and specify this location for the wizard. Keep on following the wizard an
2 - 5 Follow the wizard and browse to the folder that holds the driver and specify this location for the wizard again. The process for thi
2 - 6 port assignment setup will be required to use the USB printer as if a normal serial printer. The procedures described below may also be engage
2 - 7 the Posiflex USB interface thermal printer will operate the same way as if a RS232 serial printer connected on the COM port specified. Please
P/N: 19370900050 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with t
2 - 8 5. Power connection The power connector is a 3 pin jack between the peripheral connector and the parallel connector for PP-7000II and is at th
2 - 9 The header is printed in text mode and the rest part of this slip is printed in page mode. If FEED button is pressed at this moment, a font ta
2 - 10 release the fixing screw to adjust the position of sensor head. The acceptable paper roll bobbin outer diameter is between 18 and 22mm. This
2 - 11 accessory of the printer. If the user uses narrower paper roll and requires more spacer plates, it can be purchased from Posiflex. 4. Paper c
3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the cover. • The areas around the p
3 - 2 Before putting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions to
3 - 3 If there is no paper jam and the print head is not overheated, turn off the printer and wait for half a minute then turn it back on. If the pr
3 - 4 3. Paper Jam Problems Paper is jammed inside the printer – Turn off the printer and open the print hood by releasing the hood lock. Remove the
3 - 5 5. Advanced Analysis Tool This printer supports Hexadecimal Dump for experienced user to view exactly what data is received by the prin
i Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1
4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 64 mm Thermal h
4 - 2 C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 240 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.8 A MAX. @ 115 V AC OUTPUT V
5 - 1 V. TECHNICAL INFORMATION A. INTERFACES 1. Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin
5 - 2 B. SETUP WINDOW On bottom cover of the Aura series thermal printer, there is screwed a metal plate for setup window. In this window, there is
5 - 3 Switch position 4 defines the handshaking method in serial interface. When it is set to ON, the printer transmits an “XOFF” for busy and sends
5 - 4 Switch Position 1 2 3 4 5 6 7 8 Serial interface w/ auto cutter OFF OFF OFF OFF OFF OFF OFF OFF Parallel interface w/ auto cutter ON ON OFF
5 - 5 D. SOFTWARE COMMANDS The Aura thermal printer supports all commands applicable to Epson printer TM-T88II. The only difference is the smootheni
5 - 6 This command defines length of beep as m seconds when beep command is received. When m = 0, default applies. ESC ‘p’ m n1 n2: Kitchen bell dr
5 - 7 E. CHARACTER CODE PAGES Aura PP-7000II & PP-7000IIUSB series support all code pages and international character sets applicable to Epson p
ii GENERAL CLEANING . . . . . . . . . . . . . . . . . . . . 3 -- 1 PRINT HEAD CLEANING . . . . . . . . . . . . . . . . . 3 -- 1 TROUBLE SHOOTING
5 - 8 If any undefined code (<00> to <1F>) or an undefined <ESC>, <FS>, or <GS> command sequence beyond these tables i
1 - 1 I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading; low noise; high resolution; light wei
1 - 2 The Aura PP-7000II & PP-7000IIUSB supports a guillotine type auto cutter for paper partial cut and a manual cut mechanism. The Aura serie
1 - 3 Length of the interface cable depends on whether the order includes the power adaptor. When power adaptor is included, the interface cable is
1 - 4 E. MAIN PARTS ON THE EXTERIOR Front View Bottom View Bottom Cover Power LED Error LED Paper Out LED FEE
1 - 5 F. INDICATORS • Power LED: green • Error LED: red • Paper Out LED: red G. OPERATING ENVIRONMENT • Place the printer on a s
Kommentare zu diesen Handbüchern