Epson 4500 Bedienungsanleitung Seite 213
- Seite / 317
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Printing
Problem
Solution
The print position is
not what you
expected.
Printing starts too high
or too low on the
page.
One line of printing
has taken up two lines.
Line spacing is
incorrect.
The loading position may be incorrect. Use
micro-adjustment to adjust the loading
position. See Chapter 3. If the problem
persists, check the top margin set by your
application software and adjust it.
Auto line feed may be on. Turn off DIP
switch 2-4.
The margin setting may not be correct. Use
your application program to change the
margin.
In BASIC, enter either of the following
statements:
WIDTH LPRINT 255
GDTH
“LPT1” 255
If the printer still does not print properly,
set the right margin to the maximum
setting using ESC Q. See Chapter 9.
Line spacing is too tight or too far apart.
Use your application program to specify
line spacing using ESC 0, ESC 2, ESC 3, or
ESC A. See Chapter 9.
Troubleshooting
7-11
- Product Update Notice 2
- Using SelecType 3
- The DIP Switch Tables 5
- Graphics Character Sets 7
- PC 860 (Portugal) 8
- EPSON”,+amP 10
- IMPORTANT SAFETY INSTRUCTIONS 12
- Contents 14
- Introduction 17
- Options and Supplies 18
- Pull Tractor Unit (C800141) 19
- Multi-Font Module (#7407-A) 19
- Film Ribbon Cartridge (#7770) 19
- Introduction 3 19
- About This Manual 20
- Application Notes 21
- Where to Get Help 22
- Setting Up the Printer 23
- Unpacking the Printer 24
- 1-4 Setting Up the Printer 26
- Assembling the Printer 29
- 1-8 Setting Up the Printer 30
- Setting Up the Printer 1-9 31
- Attaching the Paper Guide 34
- Testing the Printer 36
- Running the Self Test 37
- Draft mode 42
- Letter Quality mode 43
- The Parallel Interface 45
- Connecting the 47
- Setting Up the Printer 1-25 47
- Choosing From a Menu 48
- Using Single Sheets 51
- Reloading During Printing 54
- Using Continuous Paper 55
- Loading Continuous Paper 56
- Paper Handling 2-9 57
- (25 mm) from the 58
- Switching to Single Sheets 64
- ON LINE button to set 68
- Printing on Special Paper 72
- 2-26 Paper Handling 74
- Multi-part Forms 75
- 2-28 Paper Handling 76
- Envelopes 78
- Operating the Control Panel 81
- -ON LINE 82
- -LOAD/EJECT 82
- ROMAN, LQ SANS SERIF, DRAFT 83
- -CONDENSED 83
- Setting the DIP Switches 85
- The DIP Switch Functions 88
- Page Length 89
- Skip Over Perforation 90
- The Loading Position 91
- MULTI 92
- Using Short Tear-Off 94
- Selecting Typestyles 98
- Character Fonts 99
- SANS SERIF 99
- Using the Printer 100
- 11 Spain II 102
- Choosing a Character Table 103
- Using the Data Dump Mode 105
- FORM FEED 106
- LINE FEED 106
- 3-28 Using the Printer 107
- Software and Graphics 108
- Enhancing Your Printing 109
- Character Spacing 109
- This is double-wide and 110
- Special Effects and Emphasis 111
- This is ROMAN, with both 112
- Software 112
- 10 cpi, 12 cpi 113
- Software and Graphics 4-7 114
- Graphics 116
- Income Breakdown 117
- The Print Head 117
- Twenty-four-pin graphics 118
- Pin labels 118
- 540 numbers 119
- The Graphics Command 120
- Column Reservation Numbers 121
- A Simple Graphics Program 121
- Designing Your Own Graphics 122
- 15 FOR C-1 TO 10:RESTORE 126
- 65 NEXT C 126
- User-defined Characters 127
- Draft pica 128
- Letter quality / Proportional 128
- Defining Your Characters 129
- Data numbers 130
- Software and Graphics 4-25 132
- Software and Graphics 4-27 134
- Copying ROM Characters to RAM 135
- Letter Quality Characters 136
- Superscripts and Subscripts 136
- Mixing Print Styles 137
- Using the Printer Options 139
- The Cut Sheet Feeder 140
- Paper Handling 144
- The Cut Sheet 147
- This is the first line 150
- This is line XX 150
- Single-sheet Insertion 151
- Removing the Cut Sheet Feeder 155
- The Pull Tractor 159
- LOAD/EJECT button to load the 162
- Pull Tractor 165
- Removing the Pull Tractor 168
- LOAD/EJECT 169
- PAPER OUT light 169
- The Multi-Font Module 172
- Installation 175
- SLOT by pressing the FONT 176
- Selecting a Font 176
- The Interface Boards 178
- Compatible Interfaces 179
- Installing the board 182
- FG wire attached 184
- #8143 New Serial Interface 187
- Baud rate selection 188
- Handshaking timing 188
- Error handling 188
- Maintenance 189
- Cleaning the Printer 190
- Maintenance 6-3 191
- WARNINGS: 192
- 6-4 Maintenance 192
- Replacing the Ribbon 193
- Maintenance 6-7 195
- Maintenance 6-9 197
- Transporting the Printer 199
- Maintenance 6-13 201
- Troubleshooting 203
- Problems and Solutions 204
- Troubleshooting 7-3 205
- Power Supply 206
- Printing 207
- Solution 207
- Troubleshooting 7-9 211
- Problem Solution 219
- Technical Specifications 237
- Printer Specifications 238
- Printable area: 240
- Paper weight: 241
- Paper thickness: 241
- Technical Specifications 8-5 241
- Mechanical 242
- Electrical 243
- Environment 243
- Interface Specifications 244
- Technical Specifications 8-9 245
- Interface Timing 246
- Option Specifications 248
- Storage condition: 249
- Initialization 250
- Command Summary 252
- Using the Command Summary 253
- Command Summary 9-3 254
- Control Key Chart 255
- Commands in Numerical Order 256
- Dec. Hex. Description 257
- Dec. Hex 258
- Description 258
- Command Summary 9-7 258
- Commands Arranged by Topic 259
- Control Cut Sheet Feeder 261
- 9-10 Command Summary 261
- MSB Control 262
- Data Control 263
- Vertical Motion 264
- Tab Vertically 268
- Set Vertical Tabs 268
- Command Summary 9-17 268
- Horizontal Motion 270
- Backspace 271
- Set Absolute Print Position 271
- 9-20 Command Summary 271
- Overall Printing Style 273
- Select Typestyle Family 274
- Master Select 274
- Command Summary 9-23 274
- Arranged by Topic 276
- Print Enhancement 279
- Select Subscript Mode 281
- 9-30 Command Summary 281
- Turn Underline Mode On/Off 283
- Select Character Style 283
- 9-32 Command Summary 283
- Word Processing 284
- Character Tables 285
- 0: Selects the normal set 288
- Select Graphics Mode 290
- Appendix 292
- Proportional Width Table 293
- Character 298
- Glossary 299
- 10 characters per 300
- 0, 1, 2, 3, 4, 5, 6, 7, 8 303
- 8 Glossary 306
- 1-13, 2-27 310
- EPSON”,qampti 312
- I Cancel Double-strike Mode 314
- DIP switch settings 315
- DIP Switch 1 315
- DIP Switch 2 315
- DIP switch 316
- 4500 KEY FEATURES: 317
Verwandte Produkte und Handbücher für Drucker Epson 4500
Drucker Epson T034720 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson 1200 Bedienungsanleitung
(67 Seiten)
(67 Seiten)
Drucker Epson CX5000 Bedienungsanleitung
(56 Seiten)
(56 Seiten)
Drucker Epson T549300 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson T078520 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson 60 Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Drucker Epson FX-870/1170 Bedienungsanleitung
(181 Seiten)
(181 Seiten)
Drucker Epson T078420 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson T054020 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson T549100 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson P50 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Drucker Epson T606600 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Drucker Epson 7500 Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Drucker Epson T087420 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern