Epson Apex 100 Betriebsanweisung PDF herunterladen

EPSON

Product Support Bulletin

Subject: Proper Method for Running Benchmark and Diagnostics Programs

Date: 06/04/93

PSB No: S-0158

Page(s): 1 of 1

Originator: MWT

This bulletin describes the proper method for running any benchmark or diagnostics

programs. This applies to any computer system.

In most cases, the computer should be started using an MS-DOS boot diskette

that’s ‘clean’ -

in other words, one with no CONFIG.SYS or AUTOEXEC.BAT files.

The appropriate executable can then be run, either from diskette or hard drive.

There will be some exceptions to the above rule. In attempting to benchmark or

troubleshoot any add-on that requires a device driver (CD-ROM, local area network,

etc.), obviously the necessary device driver(s) must be loaded. Also, some

programs will require a minimum number of FILES or BUFFERS to be defined in

the CONFIG.SYS file. Such programs will usually display this requirement if they

are run without the necessary CONFIG.SYS file.

For the most consistent results, use the absolute minimal boot configuration that’s

allowed by the hardware being tested.

1 2 3 4 5 6 ... 14 15

Product Support Bulletin 1

Inhaltsverzeichnis

Seite 1 - Product Support Bulletin

EPSONProduct Support BulletinSubject: Proper Method for Running Benchmark and Diagnostics ProgramsDate: 06/04/93PSB No: S-0158Page(s): 1 of 1Origin

Seite 2

PSB No: S- 0097Page: 6 of 8Q. What kind of option cards are available for the APEX 100 computer andwhere can I buy them?A. Most IBM PC/XT- compatible

Seite 3

Q.A.Q.A.Q.A.Q.A.Q.A.PSB No: S-0097Page:7 of 8How do you connect two joysticks when there is only one joystickconnector?A joystick adapter cable with 3

Seite 4

PSB No: S-0097Page: 8 of 8Q. Is the IBM 5250 emulation board compatible with the APEX 100?A. Yes, the IBM 5250 emulation board (ver. 2.1) is certified

Seite 5

Product Support BulletinSubject: Equity and Apex Series Compatibility with the System OmniBridgeController and BridgeFiler External Floppy DrivesDate:

Seite 6

PSB No: S-0088BPage: 2 of 3Equity II +Equity lIeThe Equity II + was found compatible with theOmniBridge controller.It was able to support one ortwo ex

Seite 7

PSB No: S-008BPage: 3 of 3APEX 100APEX 200The Epson APEX 100 was found compatible with theOmniBridge controller.It was able to support one ortwo exter

Seite 8

Product Support BulletinSubject:Equity/Apex Compatibility with the SOTA 386siDate:3/02/90PSB No:S-0111Page:1 of 3Originator:MS ;. CL5The purpose of th

Seite 9

PSB No: S-0111Page: 2 of 3Installation of the board in most of the units was quick and simple to do whenfollowing the installation instructions accomp

Seite 10

PSB No: S-0111Page: 3 of 3Our Computer Product Support Center receives numerous calls requestinginformation and recommendations on 80386 Accelerator b

Seite 11

Product Support BulletinSubject:Apex 100 Computer -Answers to Common QuestionsDate: 9/5/89Page:1 of 8PSB No: S-009Originator:Q. Where can I obtain hel

Seite 12

PSB No: S-0097Page: 2 of 8Q. What kind of printer can I use with the APEX 100?A. The APEX 100 includes an IBM PC - compatible parallel interface which

Seite 13

PSB No: S-0097Page: 3 of 8Q. Can a hardcard be installed in addition to a hard disk drive?A. Yes, but you must be sure that you do not mix MFM and RLL

Seite 14

PSB No: S-0097Page: 4 of 8Q. Can I add an external floppy disk drive to the APEX 100?A. Epson does not currently manufacture an optional external flop

Seite 15

PSB No: S-0097Page: 5 of 8Q. Can I use the APEX 100 Monochrome Monitor (Model # AP - 1040) withother IBM PC - compatible computers?A. The Apex 12” Mon