Epson HWDV080DV(N Bedienungsanleitung

DIRECT VENT WALL FURNACESTANDARD MODELS:HWDV080DV(N,P)-1HWDV181DV(N,P)-1MODELS WITH BLOWER:HWDV080BDV(N,P)-1HWDV181BDV(N,P)-1This appliance may be

24632-0-0508Page 10REQUIREMENTS FOR MASSACHUSETTSFor all side wall horizontally vented gas fueled equipment installed in every dwelling, building or s

24632-0-0508 Page 11TERMINATION CLEARANCESDescription US Installations1A Clearance above grade, veranda, porch, deck, or balcony 12 inches (305 mm)B C

24632-0-0508Page 12Installing a New Main Gas CockEach appliance should have its own manual gas cock.A manual main gas cock should be located i

24632-0-0508 Page 13WARNING: The nearest point of the vent cap should be a minimum horizontal distance of six (6) (1.83m) feet from any press

24632-0-0508Page 14INSTALLATION INSTRUCTIONS OVERVIEWFigure 4 Figure 5 Figure 6Location - All ModelsSelect a location near the center of the space to

24632-0-0508 Page 151Note: All references must be considered as if the observer is standing in front of the wall and/or appliance.HEATER TOBACK CASING

24632-0-0508Page 162SILICON-BASEDSEALANTMOUNTINGPLATECAPFLUE OUTLETTUBEAIR INLETTUBEFailure to position these parts in accordance with diagram or fail

24632-0-0508 Page 172INTERIOR PREPARATION AND INSTALLATION OF THE BACK OF THE UNITLocate the wall mounting plate template included in your kit and r

24632-0-0508Page 185MARKING FORWALL HOLEMARKING FORWALL MOUNTINGPLATE HOLESFLOOR LINEMARKING FORGAS INLET HOLE4Remove the template from the wall after

24632-0-0508 Page 19679Use a jigsaw to cut the holes out of the wall and discard the inner circle debris. The wall is now prepared for t

24632-0-0508Page 2TABLE OF CONTENTSSECTION PAGEIncluded in the Box ...

24632-0-0508Page 20INTERIOR INSTALLATION OF THE FRONT OF THE UNIT123Line up the two (2) tabs on the top of the wall mounting plate with the holes in t

24632-0-0508 Page 21CUTTING THE VENT TUBES124 1/2” to 12”THICK WALLThis unit is to be installed on wall from 4 1/2" to 12" (114.3 mm to 304.

24632-0-0508Page 22CUTTING THE VENT TUBES3Attach 5" (127 mm) diameter air inlet tube onto the collar of air drop assembly. Be sure 5" (127 m

24632-0-0508 Page 23312EXTERIOR INSTALLATION OF THE VENTINGAttach 5" (127 mm) diameter air inlet tube onto the collar of air drop assembly. Attac

24632-0-0508Page 246Attach 3" (76 mm) diameter flue outlet tube onto flue outlet collar on combustion chamber. FLUE OUTLET TUBECOLLAR OFFLUE OUTLET

24632-0-0508 Page 2587Installation of this Housewarmer product is complete.Attach vent cap into the 3" (76 mm) diameter flue outlet tube. Attach v

24632-0-0508Page 26123REASSEMBLY AND RESEALING VENT-AIR INTAKE SYSTEMWhen vent-air intake system is removed for servicing the furnace, the following s

24632-0-0508 Page 2765Apply furnace cement to 3" (76 mm) diameter flue outlet collar on combustion chamber and to 3" (76 mm) diameter collar

24632-0-0508Page 2878Reassembly and resealing vent-air intake system is completed.(3) #10 x ½”SCREWSAttach vent cap into the 3" (76 mm) diameter

24632-0-0508 Page 29INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB1Remove front panel of heater by opening, then lifting one side out then the other.2Di

24632-0-0508 Page 3INCLUDED IN THE BOXDIRECT VENT HEATER(INSIDE WALL MOUNTING PLATEATTACHED ON BACK)INLET & OUTLET TUBESINSTALLATION TEMPLATE(TEMP

24632-0-0508Page 304Insert blower into bottom of heater and attach with four (4) screws (provided).5Insert power cord through the hole in th

24632-0-0508 Page 316Reconnect power cord to blower assembly.7Attach ground wires from the blower and power cord to the blower mounting brack

24632-0-0508Page 329Pull blower cord from bottom to remove any excess wire from inside of the heater and attach strain relief to the cord on the

24632-0-0508 Page 33WARNINGImproper installation, adjustments, alterations, service or maintenance can cause property damage, personal injury or

24632-0-0508Page 341Do not use gases other than those indicated on the heater’s rating plate label.2Due to high temperature, the appliances

24632-0-0508 Page 35IMPORTANT: Under no circumstances should this appliance be modified. Do not operate this appliance if any parts have been remo

24632-0-0508Page 368WHAT TO DO IF YOU SMELL GAS• Do not try to light any appliance.• Do not touch any electrical switch; do not use any phone in you

24632-0-0508 Page 37OPERATING INSTRUCTIONSFOR YOUR SAFETY READ BEFORE LIGHTINGWARNING: Improper installation, adjustment, alteration, service or maint

24632-0-0508Page 38LIGHTING INSTRUCTIONS1. STOP! Read the safety information on pages 36 and 37.2. Set the thermostat (gas control knob) to lowest s

24632-0-0508 Page 3911On the main burner, the burning gas forms a primary flame and a secondary flame. The primary flame is blue and about 3/1

24632-0-0508Page 4TOOLS NEEDEDSNIPS5/16 NUT DRIVERADJUSTABLE WRENCHCAULKINGPHILLIPS SCREW DRIVERTAPE MEASUREDRILLSAWHARDWARE PACKETSPLASTIC TOGGLE (6)

24632-0-0508Page 40MAINTENANCE INSTRUCTIONSWARNING:• Prior to any maintenance operation, it will be necessary to close the gas supply.• Only qualifie

24632-0-0508 Page 41TROUBLESHOOTINGPROBLEM CAUSES SOLUTIONPilot flame does not light A) Gas supply valve closedB) Air in gas pipesC) Valve does not

24632-0-0508Page 42USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.PLEASE NOTE: When ordering par

24632-0-0508 Page 4325 R2882 R2882 BULB CLIP26 24681 24681 BLOWER WITH MOUNTING BRACKET27 R2298 R2298 VALVE MOUNTING SCREWS28 R9904 R9904 COTTER PIN29

24632-0-0508Page 44PARTS VIEW1234567891011121314151617181920212223242526272829303132333435363738394041

24632-0-0508 Page 45SERVICE NOTES

24632-0-0508Page 46SERVICE NOTES

24632-0-0508 Page 47SERVICE NOTES

24632-0-0508Page 48HOUSEWARMER is a registered trademark of Empire Comfort Systems Inc.www.housewarmerproducts.comEMPIREEMPIREComfort SystemsManufactu

24632-0-0508 Page 5GAS SPECIFICATIONSMODEL FUEL MAXIMUM INPUT MINIMUM INPUTHW080Propane/LP -- Natural gas8,000 Btu/hr 5,000 Btu/hrHW181 18,000 Btu/hr9

24632-0-0508Page 6UNIT DIMENSIONSMAKE SURE THAT APPLIANCE IS SUITABLE FOR THE GAS SUPPLY AVAILABLE:NATURAL GAS OR PROPANE/LP.

24632-0-0508 Page 7IMPORTANT SAFETY INFORMATIONChildren and adults should be alerted to the haz-ards of high surface temperatures and should stay a

24632-0-0508Page 8Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. You must find out if you can smel

24632-0-0508 Page 9Qualified Installing AgencyInstallation and replacement of gas piping, gas utilization equip-ment or accessories and repair and serv