Epson C82305 Bedienungsanleitung

EPSONSerial InterfaceCardC82305*C8230*EnglishDeutschFrançaisESpañolItaliano4000152C01-00

DIP switch 2 (interface operations)The table below contains information on switchfunctions, and the factory setting of each.Table 2.Data word structur

The table below shows the possible word structurecombinations.Table 3. Word structureYou can select the parity check method by DIP switchsettings. (Se

Baud rate selectionIn serial data communication, data is transmitted in theform of bits. These data bits go out one at a time alonga single path, and

Note• The printer will assume a setting of 1,200 BPS forswitch combinations other than those shown above.• Since the maximum transmission speed (baud

Jumper settingsTable 6. shows information about the interfaceconditions that can be selected using jumpers. In allcases, ON denotes the connection of

Table 7. Flag polarity selectionJumper FunctionFactorysettingON:MARK (do not accept data) =JNORCurrent ONONJ5JREVON: MARK (do not accept data)=Negativ

DATA ENTRYThis section gives a brief description of serial datacommunication conditions and handshaking protocolssupported by the C82305 * /C82306 * i

Handshaking protocolDTR and X-on/X-off handshaking protocols can beperformed under either RS-232D or 20mA Current Looptransmission.X-on/X-off Protocol

• Transmit timing of X-on signalThe X-on signal is transmitted when the power is firstturned on, or when the vacant area in the buffer isgreater than

With the status flag set, and data reception prohibited,the vacant area of the buffer gradually increases as theprinter continues to print. When the v

NOTICEAll rights reserved. Reproduction of any part of this manual in any form whatsoeverwithout Seiko Epson’s express written permission is forbidden

SPECIFICATIONS1.Synchronization: Asynchronous2.Baud Rate: 75, 110, 134.5, 150, 200, 300, 600,1,200, 1,800, 2,400, 4,800, 9,600, or19,200 BPS (selectab

5. HandshakingTable 8. HandshakingUsing DTR protocolUsing X-ON/X-OFFprotocolUS-232DThe two signal The impedanceconditions at pm No.between pin No. 171

HARDWARE DESCRIPTION1. I/F board connector: EIA standard 25-pin D-SUBfemale connector.2. For signal description and pin assignment, refer tothe table

Pin No. Signal Name Direction*17TTY-TXDout24TTFTXDReturnDescriptionHigh impedance (‘SPACE’)between pin No. 17 and No24 or an X-on signal sentacross

RECOMMENDED CIRCUIT CONNECTIONSRecommended line driver and line receiver for RS-232Dsignal level settings. (As viewed from the host computer.)Figure 4

INSTALLATIONThe C82305* /C82306* interface card is designed to beinstalled inside the printer. Installation or removal of theinterface board is easy,

inside the compartment.2. Fit both sides of this interface card into the guides3. Insert this interface card until the interface pins matewith the con

Current-Loop Transmitter/ReceiverCircuit DiagramsSet the Jumper Jl, J2, J3, and J4 referring to thefollowing diagrams.Transmitter Circuit Diagram121

Receiver Circuit Diagram122

EPSON OVERSEAS MARKETING LOCATIONSEPSON AMERICA. INC.2780 Lomita Blvd.Torrance. Cailif. 90505. U S APhone (213) 539-9140Fax (213) 534-5854EPSON UK LTD

Serial InterfaceC82305 * /C82306 *SchnittstellenkarteC82305 * /C82306 *Interface sérieC82305 * /C82306*EnglishDeutschFrançaisEspañolItalianoInterface

TABLE OF CONTENTSINTRODUCTIONAbout this guideSETTING THE CONDITIONSCard layoutDIP switch and jumper settingsDIP switchesJumpersDATA ENTRYSerial commun

INTRODUCTIONThe Serial Interface Card 032305 * /C82306 * is an interfacethat allows asynchronous serial data communicationbetween a host computer and

About this guideThis guide is designed to give you detailed informationon how to install your C82305 * /C82306 * serial interfacecard in a variety of

SETTING THE CONDITIONSThe C82305 * /C82306 * interface card has two sets ofDIP (Dual In-line Package) switches, and seven jumpers.These switches and j

DIP switch and jumper settingsBefore you install the C82305 * /C82306 * interface, you mayneed to adjust the DIP switch 2 and jumper settings.You can

DIP switch 1 (interface operations)The table below contains information on switchfunctions, and the factory setting of each.Table 1. DIP switch 1Switc