Epson M119A Betreibershandbuch Seite 1

Return to main menuTM-U200 Series (Type A)Operator’s ManualUsing this online operator’s guideThe words on the left side of this screen are bookmarks f

viContents Chapter 1 Setting Up the Printer Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting Up the Printer 1–1Chapter 1Setting Up the PrinterUnpackingWhen you unpack the TM-U200 Series Type A printer, make sure you have these items.If

1–2 Setting Up the PrinterThe printer should be installed so that it does not move or vibrate during paper cutting or the drawer kick-out operation.

Setting Up the Printer 1–33. Two spacers are included with the near-end detector. See the illustration below, and decide whether or not you want to us

1–4 Setting Up the Printer5. Connect the connector of the detector to CN11 on the printer. Position the cable as shown in the illustration.6. Replac

Setting Up the Printer 1–5Connecting the Printer to the ComputerYou need an appropriate serial interface or parallel interface cable to connect your c

1–6 Setting Up the PrinterThe Model with Parallel Interface1. Make sure the printer and computer are turned off. Then, plug the cable into the conne

Setting Up the Printer 1–7Plug the drawer cable into the drawer kick-out connector on the bottom of the printer next to the computer interface connect

1–8 Setting Up the PrinterDen Drucker an die Lade anschließenDas Kabel der Lade an die Schnappsteckerbuchse (neben der Schnittstellenbuchse) an der

Setting Up the Printer 1–9Grounding the Printer You need a ground wire to ground your printer. Make sure the wire meets the specification below.Thickn

TM-U200 Series(Type A)Operator’s Manual400898901

1–10 Setting Up the PrinterConnecting the Power Supply This printer requires an external power supply. Be sure to use a power supply that matches th

Setting Up the Printer 1–111. Make sure the printer and power supply are turned off.2. Plug the power supply’s cable into the printer’s connector as s

1–12 Setting Up the PrinterInstalling the Ribbon Cassette CAUTION:Never turn the ribbon cassette’s feed knob in the opposite direction of the arrow

Setting Up the Printer 1–13Note:Make sure the ribbon is installed between the print head and the platen without wrinkles or creases.

1–14 Setting Up the Printer5. Turn the ribbon cassette’s knob 2 or 3 times in the direction of the arrow again to take up any slack in the ribbon.6.

Setting Up the Printer 1–15Installing the Paper Roll CAUTION:Be sure the printer is not receiving data when you replace a paper roll. If there is data

1–16 Setting Up the Printer3. Insert the paper roll. Note:Be sure to note the correct direction that the paper comes off the roll, as shown below.

Setting Up the Printer 1–174. Open the auto cutter by pulling the tab up and toward you.

1–18 Setting Up the Printer5. Hold both edges of the paper and insert it straight into the paper slot. The printer feeds the paper automatically.6.

Setting Up the Printer 1–197. Insert the journal take-up spool in the printer.8. Cut the receipt paper (when using a 2-ply roll paper) on the manual c

Note:Everything in this manual applies to the TM-U210 printer.Printer parts and LabelsPrinter coverDrawer kick-out connectorsPower connectorInterfa

1–20 Setting Up the Printer2. Cut the journal and receipt paper as shown in the illustration below.3. Remove the paper take-up spool from the printe

Setting Up the Printer 1–21Note:Be sure to install the ribbon cassette and the paper roll before you run the self test.1. To perform the self test, ho

1–22 Setting Up the Printer2. Turn the printer over and remove the DIP switch access cover, as shown below.3. There are two sets of switches. Use tw

Setting Up the Printer 1–23 CAUTION:Do not change the settings of switches 2-2, 2-3, 2-5, and 2-6. Changing these settings may cause inferior print qu

1–24 Setting Up the Printer CAUTION:Do not change the settings of switches 2-2, 2-3, 2-5, 2-6, and 2-8. Changing these settings may cause inferior p

Setting Up the Printer 1–25Using the Power Switch CoverYou can use the provided power switch cover to protect the power switch from accidental or impr

1–26 Setting Up the PrinterAffixing the Fastening Tape (Option)Two sets of tape are included as an option to fasten your printer to a countertop or

Using the Printer 2-1Chapter 2Using the PrinterOperating the Control PanelYou can feed paper with the button on the control panel. The indicator lig

2-2 Using the PrinterIndicator lightsThe control panel lights provide information on printer conditions.POWER (Green)The POWER light is on when prin

Using the Printer 2-3 CAUTION:The print head becomes very hot during printing. Allow it to cool before you reach into the printer. Note:The power sw

Control panelCaution Labels CAUTION:Head cover and printer head are hot. CAUTION:Caution label for drawer kick-out.Instruction LabelPAPER FEEDbutto

Troubleshooting 3-1Chapter 3TroubleshootingTroubleshooting This chapter gives solutions to some of the more common printer problems.General problems

3-2 TroubleshootingThe ERROR light is off, but nothing is printed.Try to run the self test to check that the printer works properly. See the self te

Troubleshooting 3-3A line of dots is missing in the printout.The print head may be damaged. Stop printing and contact your dealer or a qualified ser

3-4 Troubleshooting3. Remove the paper roll from the printer.4. Open the auto cutter by pulling the tab up and toward you.5. Remove the jammed paper

Troubleshooting 3-58. Loosen the screw securing the print head cover. Turn the screw only until you can tilt it as shown in the illustration. Note:

3-6 Troubleshooting9. Lift up the print head cover.10. Remove all the jammed paper. Note:Do not pull the jammed paper in the opposite direction of

Troubleshooting 3-713. If the auto cutter blade is not in its normal position (if you can see the blade in the auto cutter slit, the blade is not in

3-8 TroubleshootingTo use the hex dump feature, follow these steps:1. After you make sure that the printer is off, set DIP switch 1-2 to ON.2. Turn

Reference Information 4-1Chapter 4Reference InformationPrinting Specifications Note:When printing exceeds the allowable print duty cycle, the print

4-2 Reference InformationCharacter SpecificationsCPL = Characters per lineCPI = Characters per inchLPS = Lines per secondANK = Alphanumeric characte

iAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechani

Reference Information 4-3Paper SpecificationsPaper feed method: Friction feedPaper feed pitch: Default 4.233 mm (1/6 inch)Can be set in units of 0.1

4-4 Reference InformationPressure sensitive paperMaximum 1 original + 1 copySize: Width 76 mm ± 0.5 mm (3.0" ± 0.02")Maximum outside diame

Reference Information 4-5Electrical SpecificationsPackaged AC adapter: One of the following 5 AC adapters is selected, depending on local power:Note

4-6 Reference InformationReliabilityLife: Mechanism 7,500,000 lines Print head: 150 million characters(at an average of 2 dots/wire per character

Reference Information 4-7Environmental ConditionsTemperatureOperating:Storage:0 to 50° C (32 to 122° F) (when the temperature is 34° C or more, ther

4-8 Reference InformationInterface SpecificationsNote:The interface is a factory-installed option. One of the following interfaces is already instal

iiFCC CLASS AFCC Compliance StatementFor American UsersThis equipment has been tested and found to comply with the limits for a Class A digital device

iiiProduct Name: PrinterModel Name: M119A This printer conforms to the following Directives and Norms:Directive 89/336/EECEN 55022 (1987 and 1994 2nd/

ivIntroductionFeaturesThe TM-U200 Series Type A printer is one-station printer for ECR and POS use that can print the results of weighing or measuring

vAbout This ManualSetting Up and Using❏ Chapter 1 contains information on unpacking the printer, setting it up, running the self test, and setting the