EPSON ®ACTION SCANNER™ IIColor ScannerGetting Startedfor Windows@Printed on recycled paper with at least 20% post-Consumer content
Setting Up the ScannerFollow these steps to set up the scanner:1.Take the scanner out of its box and place it on a flat, stablesurface with the rear p
5.Connect one end of the power cable to the power inlet onthe rear of the scanner and plug the other end into anappropriately grounded electrical outl
Connecting the Scanner to the ComputerFollow these steps to connect the scanner to your computerand, for Windows 95, to configure the scanner port:1.T
Configuring Parallel Port LPT2 for Windows 95Follow these steps to detect port LPT2 and then disable it as aWindows 95 printer port so you can use it
Installing the EPSON Scanning UtilitiesThe EPSON Scanning Utilities include EPSON Scan! II andEPSON TWAIN. Scan! uses TWAIN to capture images andthen
5.6.7.8.9.Choose OK to accept the default pathname in which theprogram will install the utilities.The next screen prompts you for the pathname of theW
After a few moments, the scanned image appears in theEPSON Scanner Setup dialog box, as shown below.If the image does not appear, choose Cancel and re
3.4.5.6.7.8.9.If you are running Windows 3.1 Program Manager, open theFile menu and choose Run. You see the Run dialog box.Type A: SETUP (or B:SETUP,
If you are running Windows 95, click Start and then selectPrograms. Click the Image-h Easy Pack folder and thenselect Image-h for Epson.12. From the F
After you choose an image, follow these steps to scan it:1.Raise the document cover on the scanner and place theimage face down on the glass surface.2
A Note Concerning Responsible Use ofCopyrighted MaterialsLike photocopiers, scanners can be misused by improper copying of copyrighted material.Althou
5.Select Scan. TWAIN pre-scans and then scans your image.6.In a few moments, the scanned image is imported into theImage-In window. Choose Close to ex
Calibrating Your SystemCalibration allows you to match your scanner and your outputdevice so you can reproduce color images that are very close tothe
You see this screen:I-IAdjust the slider below until the. grayareas appear the same. 3.Look at the display from a distance and adjust the slide barunt
Exporting a calibration chartTo calibrate your printer to your scanner, you need to export acalibration chart from Scan! II to your application and th
3.In the File Name field, type the name you want to use forthe calibration chart file, such as COLORl.BMP.4.Choose OK to export the calibration chart.
6.7.8.9.Choose Continue; you see the EPSON TWAIN advancedscreen.If necessary, select Color Photo from the Image Typepull-down menu.Select Calibration
6.Choose OK. You see the EPSON TWAIN advanced screen.7.Select the Scan button. The scanner scans using the information in the calibration profile to
To scan at the optimum resolution for your image and final output device, select your resolution based on the recommendations in the table below. The
ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 1System and Memory Requirements . . . . . . . . . . . . . 2Installing the P
This package contains everything you need for professionalquality color scanning:00cl00EPSON© ActionScanner©II color scanner, which scans infull color
System and Memory RequirementsFor the scanner hardware and software to work properly, yoursystem must include the following minimum configurationliste
Windows 95 Requirements:0A 386-based (or higher) IBM compatible computer or anIBM PS/2LiMS-DOS version 5.0 or higher0 Microsoft Windows 9503.5-inch, h
Installing the Parallel lnterface CardFollow the steps in this section if you need to install thebidirectional parallel interface card in your compute
1.2.3.Carefully remove the interface card from its packaging,holding it only by its top edges. Then place it on a flat,clean surface.mCaution:Avoid to
Follow these steps to install the card in your computer:1.Turn off the computer and any peripheral devices.2.Disconnect the computer’s power cable fro
Kommentare zu diesen Handbüchern