Epson GT-8500 Betriebsanweisung

EPSON®@aPrinted on recycled paper with at least 10% post-consumer content

Installing the EZ-SCSI SoftwareIf you are running Windows NT, you do not need to installEZ-SCSI or the EPSON Scanning Utilities; skip to “InstallingAd

10. Remove the last installation diskette from the drive andchoose Continue.Installing the EPSON Scanning UtilitiesThe EPSON Scanning Utilities includ

7. The next screen prompts you for the path name of theWindows directory. If the displayed path is correct, chooseOK. (Otherwise enter the correct dri

10. Choose Test. If the scanner, SCSI interface, and EPSONScanning Utilities are set up correctly, the scanner scans theimage. After a few moments, th

Installing PhotoshopFollow these steps to install Photoshop :1. Start Windows, if necessary2. Insert the Photoshop Installer-Disk 1 in a diskette driv

7. Enter your name, organization (optional), and the serialnumber of the program. You’ll find Photoshop’s serialnumber inside the front cover of the P

3. Highlight Epson Scanners if it is not already highlighted4. Choose Select to specify the scanner as the acquire device.5. Select Exit from the File

7. Follow the instructions as they appear on the screen forinserting the other TextBridge diskettes and choose OK.8. When you see a message telling yo

Scanning ImagesNow you are ready to start scanning. First, choose an image toscan. The best choice is a color photograph. Printed pictures,such as tho

3. Carefully close the document cover so that you do not disturbthe position of the photograph on the glass.4. Choose Acquire in the File menu; then c

A Nofe Concerning Responsible Use ofCopyu-gh fed MaferialsLike photocopiers, scanners can be misused by improper copying of copyrighted material.Altho

5. In the scroll bar next to the Image Type button, select theimage type appropriate for your scan. If you are scanning acolor photograph, select Colo

7. Select Scan. In a few moments, the scanned image isimported into the Photoshop window.8. To see the scanned image, select Close to exit EPSONTWAIN

Calibrating Your SystemCalibration allows you to match your scanner and your outputdevice so you can reproduce color images that are very close tothe

2. Choose Screen Calibration from the Calibrate menu. You seethis screen:Adjust the slider below until the grayareas appear the same.3. Look at the di

When screen calibration is enabled, TWAIN uses it as it scansimages until you change this setting.Note:If you change to a different monitor, you will

5. Exit EPSON Scan! II.6. Start Photoshop by double-clicking on its icon in the Adobeprogram group.7. Open the calibration chart file you exported. Th

4.5.6.7.8.9.In the File Name field, type the file name of the calibrationfile you want to create, such as COLORl.CAL. Make sureyou use the .CAL file e

5. Choose Add6. Choose OK. You see the EPSON TWAIN screen.7. Now scan your image by choosing the Scan or Auto Scanbutton.The scanner scans the image u

Note that a very high resolution scan may not produce abetter-quality printed image because your output device maynot recognize the high resolution in

In troduc tionThis package contains everything you need for professionalquality color scanning:EPSON® ES-1000C’“color scanner, which scans in full col

System and Memory RequirementsFor the scanner hardware and software to work properly, yoursystem must include the following minimum configuration:A 38

Installing the SCSI Interface CardFollow the steps below to install the SCSI interface card in yourcomputer. For additional information, see the manua

7. Unpack the interface card. When handling the card, be carefulnot to touch any of the components on the circuit board orthe gold-edged connector.8.

5. Connect one end of the power cable to the power inlet onthe rear of the scanner and plug the other end into anappropriately grounded electrical out

Connecting the Scanner to the ComputerFollow the steps below to connect the scanner to yourcomputer’s SCSI interface using the cable included with the

4. Make sure the scanner’s internal SCSI terminator switch isturned on, as shown.5. Make sure the SCSI ID switch is set to 2, as shown6. Turn on the s